Seismic Strengthening for Structures in Regions of Low Seismicity
Most existing structures were not designed to today's seismic codes and standards, and in fact in low seismicity regions codes did not require seismic design until recently....
Axial Capacity of Concrete Infilled Steel Box Column with Biaxial Bending
The objective of this study was to investigate the feasibility of using the Bresler reciprocal load method to calculate the axial capacity of a concrete infilled steel box column subjected...
An Innovative Connection Detail for High-Rise Buildings
Composite columns consisting of hollow steel tubes filled with high strength concrete have been used in high rise building construction in the USA and Far East Asian countries. The focus...
Behavior and Design of Angle Connections Subjected to Cyclic Axial Force and Shear
The objectives of this study were to establish cyclic behavior of double angle shear connections subjected to axial load and to develop design recommendations. Five cyclic tests of double...
Composite Beams and Joists
Composite beams and joists used as flexural members in multistory steel-frame buildings are considered. Research results have shown that present design values for headed shear studs, used...
Flexural and Shear Behavior of Combined Concrete and Graphite Epoxy Beams
An experimental and analytical study of six graphite composite beams are presented. Four of the beams incorporated a reinforced concrete slab. The composite action and the effect of concrete...
Strength, Behavior and Repair of Masonry Infills
Results of a series of experiments are presented on seismic performance of unreinforced masonry infill panels. The object of the investigation is to examine the loss of out-of-plane strength...
QST Rolled Shapes, a New Generation of HSLA Compression Members
With the development of the Quenching and Self-Tempering (QST) process by the Luxembourg steelmaker ARBED S.A., a new generation of High Strength Low Alloy (HSLA) rolled shapes has become...
Three-Dimensional Stability Analysis of Carpenter Dam
This paper describes the three-dimensional stability analysis of Carpenter Dam. The presence of keyed construction joints between dam monoliths at Carpenter Dam can significantly affect...
Graham Lake Dam Remedial Measures Project
Graham Lake Dam consists of a 550-foot long earth embankment and an 80-foot long concrete spillway. Several concerns were identified during project inspections including limited spillway...
Evaluation of Rehabilitation Needs for Hydraulic-Fill Dam
This paper describes the application of analytical methodologies developed for seismic stability analysis of dams in the western U.S. (particularly the Lower San Fernando Dam in Southern...
Seismic Rehabilitation of Sardis Dam
Extensive subsurface investigation of the embankment dam revealed the existence of a weak layer of silt and soft clay in the original topstratum clay underlaying the upstream shell of...
Accelerator for Shotcrete Based Amorphous Calcium Aluminate
The authors developed an accelerator based on amorphous cacium aluminate named NATMIC for shotcrete. In Japan, accelerator based amorphous calcium aluminate are widely used in shotcrete...
The Causticity of Accelerator for Shotcrete and its Impairment on Strength of Shotcrete
How on earth is the toxic and caustic injury of accelerator for shotcrete to operators and animals? How about its impairment on strength of shotcrete? The paper gives some reports and...
Steel Fibre Reinforced Shotcrete Design
There is a need for introducing toughness and ductility in SFRS design. The Japanese Standard introduces the equivalent flexural strength, which characterizes SFRS toughness and allows...
Adapted Actions Taken at Too Low Shotcrete Quality
A tunnel contract specified quality parameters such as: thickness, compressive strength, adhesive strength, bending tensile strength and residual bending tensile strength for fibre reinforced...
Open Channels in Fractures Maintained by Deposition and Erosion of Colloids
Colloids initially suspended in the water in fractures can deposit onto the fracture surfaces, and will partially or fully clog the fracture. The amount of clogging will depend on whether...
Geometric Analyses of Alternative Models of Faulting at Yucca Mountain, Nevada
Realistic cross section tectonic models must be retrodeformable to geologically reasonable pre-deformation states. Furthermore, it must be shown that geologic structures depicted on cross...
A Generalized Three Invariants Cap Model and its Numerical Implementation to Study Soil-Foundation Interaction
This paper presents a modified cap model that is capable of characterizing cyclic stress-strain behavior of soils and describing variation of shear strength along various stress paths...
Subsidence Properties of Holocene Sediments: S. La.
As part of a comprehensive USGS-sponsored study of processes that drive subsidence and wetland loss in south Louisiana, two continuously cored deep borings (60 m and 72 m) were acquired...
Return to search